Bathroom Zones For Electric Towel Rail

Zone 2 Is the area 600mm above or to the side of the bath and shower and still 225m from the floor. The work should have been notified to building control under part P of the building regulations so due to the cowboy that you hired to fit the radiator they have now exposed.

Towel Warmers Electric Radiators Valves Radiators Towel Warmers Electric Underfloor Heating

Inside the bath or shower.

Bathroom zones for electric towel rail. At Heater Shop we have a wide selection of energy efficient electric towel rails for all styles and and configurations with an IPX4 rating or above ensuring total confidence and protection. Zone 1 the area directly above zone 0 limited vertically to 225m above the bottom of the bath or shower also 12m horizontally from the centre of a shower outlet to the height of the outlet or 225m whichever is the higher Zone 2 the area beyond zones 0. Fitting an electric radiator in your bathroom must comply with IP Ingress Protection ratings within bathroom zones.

Bathroom zones are areas where electrical equipment must offer a certain degree of protection against water. A lesser IP rating will require a warmer to be installed in Zones that are further away from the water source which. I am uncertain of how the regs apply here but if I understand them I can install an IPx4 rated rail using a fused connection unit with no switch but provide an isolator switch outside the bathroom or via a pull chord.

Above the bath or shower to a height of 225m. It is the responsibility of the installer to assess the actual installation environment to establish suitability in the specific location. I mounted mine outside the bathroom wall.

Finally note that the power needs to be sourced from an RCD protected supply. They are not suitable for installation in Zone 0. Why not install a timer to your electric heaters and never wake up or come home to a cold home again.

Normally to put a heated towel rail in a bathroom then the towel rail flex would go in a flex out let and from there the fuse would be out side the bath room the end. This method prevents unsightly cords from showing because it does not plug into an electrical outlet. Zone 2 covers the area 600mm above or to the side of the bath and shower and 225m from the floor.

Although electrical devices are unlikely to get wet in Zone 2 it is still a potential splash zone so a minimum of IPX4 is required and again only 12V. Heated towel rails have an IP Rating suitable for zone 2 whereas most electric heaters do not carry this rating. It is also a great method if you dont have a radiator in your bathroom.

Something as simple as an electric heated towel rail can transform the feeling of your bathroom. The diagram shows a bathroom split into four clear zones. The switch for the towel rail has to be out of zone.

All Kudox Electric Towel Rails are rated IP55 for installation in IEE Bathroom Zones 1 2 along with the all areas outside the zones. Alternatively put the towel rail in Zone 2 with a swspur or isolator switch more than 600mm from the bathshower so that it is no longer in Zone 2 but still near the towel rail. Any Lighting used here must have a minimum rating of IP67 protected against immersion in water Zone 1.

Zone 0 This is the area occupied by elements such as the bath or shower. Each of the bathroom electrical zones illustrated below has specific requirements regarding the electrical equipment that can be installed and used in that zone. Running costs from as little as 6 cents an hour thats right less than 140 euros a day.

Luxury you cant afford to miss Heated towel rails were once considered a luxury but did you know that a standard Thermorail dry electric heated towel rail can cost as little as one cent an hour to run. This option may be limited by the sizeshape of the room but worth considering. Your electrician is right a switched fused spur inside the bathroom is totally unsafe and not compliant with BS76712008 wiring regulations.

IPX4 means it has water splash resistance from any direction. The lower the zone number the higher the IP rating needs to be. THis IP rating determines in which bathroom IP zone the towel warmer can be installed.

Zone 2 Minimum IPX4. The third way to install a heated towel rail is by hard wiring the rail into the electricity of the bathroom. IP45 warmers can be installed in Zone 1 which offers peace of mind by ensuring the most installation flexibility.

Install a bathroom towel rail and have warm dry towels every morning and evening this winter. The requirement for both Zones 1 and 2 are the same - the equipment has to be IP rated IPX4 - my towel rail is rated IP56 so easily complies. Any electrical fitting or appliance within zone 1 must be IPX4 as well as 12V SELV.

Zone 2 is an area stretching 06m outside the perimeter of the bath and to a height of 225m from the floor. For example Zone 0. There is nothing like a warm dry towel.

However working with electrical currents is dangerous. The electrical connection to the power supply for these appliances must be in Zones 23 of the bathroom in compliance with BS 76712008 2011 - IEE Wiring Regulations. IP bathroom zones are determined by ASNZS 30002007 and are identified on these diagrams.

0 1 2 and Outside Zone also known as Zone 3. I would be grateful if anyone can confirm this please. Zone 1 is the area directly above zone 0 and a height of 225m from the floor.

The bathroom zone number refers to the amount of water likely to be present. I have been asked to fit subject item in zone 2 in a bathroom. No devices are allowed in this zone apart from suitable equipment or insulated pull cords.

Can I Put An Electric Radiator In The Bathroom