The shower-head is hooked about 03m on the right side of the bath but is designed to be held in the hand during use. This is done to avoid any splash backs onto the socket.
Ip Ratings In Damp Areas Bathroom Lighting Bathroom Light Fixtures Bathroom Light Fittings
Providing the Shaver socket is reduced to 110V it should go in zone 2 or preferably zone 3 never in zone 1.
Bathroom zones for shaver socket. If you do have an electrical shaver point installed it must be a safe distance in. Sockets incorporated into a shaver electrical supply unit. From first principles I reckon the isolating transformer in it will provide safety even for someone standing in the bath.
Specially designed shaver units are an exception to this rule and can be located slightly nearer but still no closer than 600mm from the bath or shower. Zone 0 for a bathroom is the area inside the bath. Zone 2 for a shower room is the same height as zone 1 extended to 06m around the shower basin.
If you would prefer to keep your shaver socket out of this area by all means do. Some organisations extend Zone 2 to around the wash basin. What else do the regs insist on if its here.
Shaver sockets are a special case as we have mentioned above. Safety When You Install A Shaver Socket This means it is safe to use in the bathroom. They have to be certified for use in a bathroom different zones within the bathroom.
Shaver sockets should be installed 300mm from the edge of the sink unit or you can site the shaver socket in zone 2 which runs from the edge of the bath or shower cubicle to a distance of 600mm from the bath shower cubicle up to the height of 225m. And is there logic to this or just a rule. Electrical shaver points must be a safe distance in meters from the bath or shower to avoid splashes.
The only exception to this is a shaver-supply unit. Plate switches can be used outside the zones and when deemed suitable for use in a bathroom by the manufacture. Unless your mounting them in an odd.
Under bath depending if panel is removable with a tool or not decides on what Zone comes under but nothing about inside a sink unit. A shaver supply unit complying with BS EN 61558-2-5 may be installed in zone 2 of a location containing a bath or shower Regulation 7015123 refers. You can site the shaver socket in Zone 2 which runs from the edge of the bath or shower cubicle to a distance of 600mm from the bath or shower cubicle up to a height of 225m.
A shaver socket-outlet with a transformer is called a shaver supply unit. I want to put a shaver socket at the edge of zone 2 basin which may be just inside zone 1 bath. Also its worthy to note that there should be no 240V sockets in the bathroom at all.
The term shaver supply unit means. The shaver unit is approx 1m above the left hand side of the bath within Zone 1. However if the space under the bath or shower basin is only accessible with a tool it is considered to be outside the zones.
Electrical Sockets Electrical sockets are permitted in bathrooms or shower rooms as long as they are located more than 3m from the edge of the bath or shower. An accessory embodying a shaver transformer and one or more socket-outlets. Cant seem to find any exact answer to what Zone is inside sink unit.
If there is no shower basin zone 2 is replaced by zone 1 extended to 12m around the fixed shower head. I wanted to add a socket in the bathroom but seem to be getting conflicting information from people and documentation unless I am interpreting the SANS documentation incorrectly. According to the updated 17 th edition of the IEE Wiring Regulations it is safe to install electric shaver sockets in your bathroom providing the socket is 110v and installed in zone 2 or beyond with at least a 3-metre gap from either the bath or shower.
I am in the process of adding an ensuite bathroom to my bedroom. Switches are permitted in Zone 2 only if theyre installed higher than 03m above the bathroom floor with IPX4 specification which protects it from splashes of water. This type of shaver supply unit which incorporates a safety isolating transformer is the only type which is permitted in a bathroom or shower room.
Zone 0 for a shower room is the area inside the shower basin. Can see basin is Zone 2 and extends around basin 600mm from basin bath edge is out of Zone. If there is no shower basin zone 0 is 10cm high from the finished floor level and extends to 12m around the fixed shower head.
I feel this is a dangerous situation - I have a four year-old daughter and I am very concerned. The use or installation of sockets is not allowed in bathrooms or shower rooms unless they can be fitted at least 3 metres from the bath or shower. Where you can only install in zone 2 ensure that the you place your shaver socket as far away from any water sources as possible to reduce any chance of splashing.
Zone 1 for a bathroom is the same width as zone 0 the width of the bath extending to 225m above the finished floor level. Zone 2 but must be located where direct spray from showers is unlikely. The space under the bath tub or shower basin is considered to be zone 1.
Zone 2 for a shower room is the same height as zone 1 extended to 06m around the shower basin. Zone 2 Zone 2 for a bathroom is the same height as zone 1 225m extended to 06m around the bath. Additionally can you put a shaver socket in a bathroom.
Its the safety isolation transformer is critical - it must have the BS EN compliance Regards OMS. Shaver sockets are 240v or 120v but are isolated via a transformer. You can site the shaver socket in Zone 2 which runs from the edge of the bath or shower cubicle to a distance of 600mm from the bath or shower cubicle up to a height of 225m.
Sockets are not allowed in bathrooms or shower rooms apart from shaver-supply units unless they can be fitted at least three metres from the bath or shower. From SANS 10142-1-2009 section 71433 it seems one can install a socket in zone 3 provided it is on earth leakage. Zone 2 for a bathroom is the same height as zone 1 225m extended to 06m around the bath.
Pull cord switches are allowed in Zones 1 and 2 and are recommended as they suitable for high humidity condensation environments.
Lights Above Bathroom Mirror Bathroom Lighting Bathroom Lights Over Mirror Bathroom Wall Lights
Backlit Mirror Shaver Socket 600mm X 520mm Mirror Backlit Mirror Lamp
Shaver Sockets Are Ideal For Toothbrushes And Hair Straighteners Too Sockets Can Be Hidden Away Discreetly In Your C Locker Storage Shower Room Bathroom Style
Knightsbridge Led Illuminated Bathroom Wall Mirror Ip44 Shaver Socket Electrical World Rectangular Mirror Led Mirror Bathroom Mirror Wall Bathroom
Pin On Blissful Bathrooms
Bathroom Shaving Cabinet With Mirror Shelves Google Search Bathroom Mirror Cabinet Unique Bathroom Mirrors Bathroom Mirror Lights
6804 Snaresbrook Frame Your Bathroom With The Tp24 Landscape Mirror With Shaver Socket Bathroom Mirror Mirror Bathroom Lighting
Bathroom Lighting Zones Regulations The Lighting Superstore Bathroom Lighting Bathroom Light Fixtures Bathroom Light Fittings
The Lighting Book Alto Bathroom Wall Light With Shaver Socket P62 3008 Medium Jpg 665 6 Bathroom Lighting Traditional Bathroom Lighting Bathroom Ceiling Light
0 comments:
Post a Comment